How do you light a Williams wall furnace

Gas Heaters For old wall heaters, after turning the dial towards ‘Pilot’, hold down on the pilot gas button, instead of the ignite button. After about 30 seconds, release the button. Then, press the button again to light up the pilot. The new wall heaters ignite the pilot light with a spark.

How do you light a gas wall furnace?

How do you light a self igniting furnace?

Press the gas control knob down all the way and hold it in the depressed position. If you have no igniter, move the match or barbecue lighter flame to the end of the pilot tube; the pilot flame should light immediately. If you have a spark igniter, press the ignition button until the pilot flame ignites.

Where is the reset button on a Williams wall heater?

3) Press/hold RED reset button (upper top left side of heater assembly; two wires were connected to it) for about 2 seconds. It immediately fired up.

How do you start a gas wall heater?

To turn on your gas heater, locate the knob for starting. …
Turn the knob to “Pilot,” and then push down on the “Ignite” button. …
Once the pilot light comes on, hold down the Ignite button for 10 to 15 seconds.
Set the temperature on the wall heater to your desired heating level.

How does a wall heater work?

Wall furnaces house a pilot light, much like a water heater. …
Wall heaters produce heat through the wall heater and not a ducting system, so they will heat a small space quickly and maintain the heat in the room.

How do you light a propane wall heater?

Open the valve control knob on the propane tank by turning it counterclockwise.
Push in and turn the knob on the front or side of your heater to the “Start” or “Light” position.
Push and hold the knob to unlock the propane valve in the heater and send gas to the unit.

Why won't my pilot light stay lit on my furnace?

If your pilot light won’t stay alight, it might be the thermocouple. Sometimes dust buildup collects on the thermocouple and blocks the sensor. Try cleaning the thermocouple and then relighting the pilot light. If it continues to go out, the thermocouple might need to be replaced.

Where is the reset button on a wall furnace?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

How do I light the pilot light on my furnace?

First, locate the pilot valve on the furnace. …
Find the gas valve and turn it to the “off” position. …
Turn the valve to the “pilot” position.
Press and hold the reset button.
If the reset button fails, ignite the lighter.

Article first time published on

How do I know if my furnace is gas or electric?

If you see a blue flame, it’s a gas heat exchanger. Other units will have a small metal panel that’s easy to remove. You can check behind there to see if you see that blue flame. Electric systems don’t have that access window or panel and make very little noise.

How do you light the pilot on a gas furnace?

Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.

How do you adjust the pilot light on a gas wall heater?

Turn that screw counter-clockwise, and the flame should grow. Do this if you believe your flame is too low.
Rotate the screw on the pilot light clockwise, and the size of the flame will decrease. …
Return the access place to the front of your gas furnace.

Why does the pilot light go out on my wall heater?

If your furnace pilot light keeps going out, it’s likely you have a broken thermocouple in your gas furnace. The thermocouple is a rod that comes into physical contact with the flame in your system. … When this component is not able to detect the flame, it will close the gas valve to prevent a gas leak in your home.

How does a wall furnace thermostat work?

Mechanical thermostats regulate heat thanks to the expansion of their internal metallic strips. This strip carries electricity through the connected circuit, switching on the heating. As the strip heats up, one of the metals expands enough to open the circuit and switch off the heating, cooling the room down.

How do wall heaters vent?

The wall furnace vents the LP or natural gas fuel combustion gases through a horizontal wall vent to the building exterior.

Should the pilot light always be on in a gas heater?

Most furnaces with electronic ignition have a device called a hot surface igniter. … The difference is that the flame is only lit (by an electronic spark) when your furnace is ready for a heating cycle. When the pilot light is not needed, it is completely off, saving you money on gas.

How long does it take for furnace to reset?

Either way, restarting a furnace is a relatively simple task that takes no longer than 10 minutes to complete. Follow these steps to reset your gas furnace: Turn the circuit breaker off and switch the furnace power button off too.

How do I reset my heat?

Turn your thermostat “off”, then flip the related circuit breaker “off”. Wait 30 seconds, then turn the breaker back “on,” then the thermostat. Set the thermostat to hot or cold, whichever you prefer, and your desired temperature. This should effectively reset it.

Why does my wall heater keep turning off?

If your furnace keeps shutting off, it could be due to low airflow. There are several indirect issues that cause low airflow. Dirty Air Filters. If you don’t change your air filters often enough, the filters will become dirty and clogged, which means the heat exchanger retains heat and eventually causes it to overheat.

Can I relight the pilot light by myself?

If your pilot light goes out, your furnace will not be able to produce heat because its burners will not ignite. Often, homeowners can relight the pilot themselves.

Why is my furnace not igniting?

The pilot light or ignition sensor is usually the most common issue when your furnace will not ignite. … Then, remove the front panel to find the ignitor or ignition sensor. This is typically located near the burners. If the sensor or ignitor is dirty, it will need to be cleaned.

Where is the ignitor on my furnace?

Unscrew and remove the service panel on the side of the furnace and find the ignitor. It is usually mounted on a V-shaped bracket near the gas port. The ignitor has two wires attached to the back of it and has a flat metal tip.

Does an electric furnace have a pilot light?

A pilot light is the small blue flame that ignites the burner in your furnace. Most newer furnaces have electric starters, rather than pilot lights, but they’re common in older systems. But here are a few tips on how to re-light your pilot light should it ever get snuffed. …